Emerson 1367 High-Pressure Instrument Supply System User's Guide

(0 Votes) | (0)
Page / 2
Type 1367
D100343XENG
Installation Guide
English – May 2002
www.FISHERregulators.com
Introduction
This installation guide provides instructions for installation,
startup, and adjustment. To receive a copy of the instruction
manual, contact your local Fisher Sales
Office or Sales Representative or view a copy at
www.FISHERregulators.com. For further information refer to:
Type 1367 Instruction Manual, form 5220, D100343X012.
This installation guide provides basic information on the
Type 1367 high-pressure instrument supply system. For
complete adjustment, maintenance, and parts informa-
tion on the individual components of this system, refer to
separate manuals for the Type 67CF and 1301F regula-
tors, Type 252 filter, and Type H800 relief valve.
The Type 1367 high-pressure instrument supply system
takes a pressure of up to 138 bar (2000 psig) and re-
duces it to a controlled pressure to be used for supplying
a pneumatic instrument. This system consists of the fol-
lowing:
A Type 252 aluminum extended body filter.
A first-stage Type 1301F regulator, with bracket for mount-
ing on an actuator yoke or casing.
A Type H120 relief valve, elbow-mounted in the side
outlet of the Type 1301F regulator.
A second-stage Type 67CF filter-style regulator, nipple-
mounted in the outlet of the Type 1301F regulator.
A Type H800 relief valve, nipple-mounted in the outlet of
the Type 67CF regulator
P.E.D. Categories
This product may be used as a safety accessory with
pressure equipment in the following Pressure Equipment
Directive 97/23/EC categories. It may also be used out-
side of the Pressure Equipment Directive using sound
engineering practice (SEP) per table below.
EZISTCUDORPSEIROGETACEPYTDIULF
)hcni-4/1(6NDPES1
Specifications
Connection Size
Inlet and Outlet: DN 6 (1/4-inch) NPT screwed
Type H800 Vent: DN 15 (1/2-inch) NPT screwed
with removable screen
Maximum Inlet Pressure
(1)
138 bar (2000 psig)
Outlet (Supply) Pressure Range
(1)
0,34 to 2,4 bar (5 to 35 psig)
Maximum Outlet (Supply) Pressure with Type
67CF Regulator Failed Wide-Open and Type H800
Relief Valve Relieving
(1)
3,4 bar (50 psig)
Proof Test Pressure
All Pressure Retaining Components have been
proof tested per Directive 97/23/EC - Annex 1,
Section 7.4
Temperature Capabilities
(1)
-29 to 66°C (-20 to 150°F)
Installation
Only qualified personnel should install or service
a regulator. Regulators should be installed,
operated, and maintained in accordance with
international and applicable codes and
regulations, and Fisher instructions.
If the regulator vents fluid or a leak develops in
the system, it indicates that service is required.
Failure to take the regulator out of service
immediately may create a hazardous condition.
Personal injury, equipment damage, or leakage
due to escaping fluid or bursting of pressure-
containing parts may result if this regulator is
overpressured or is installed where service
conditions could exceed the limits given in the
Specifications section, or where conditions
exceed any ratings of the adjacent piping or piping
connections.
To avoid such injury or damage, provide pressure-
relieving or pressure-limiting devices (as required
by the appropriate code, regulation, or standard)
to prevent service conditions from exceeding
limits.
Additionally, physical damage to the regulator
could result in personal injury and property
damage due to escaping fluid. To avoid such injury
and damage, install the regulator in a safe
location.
Clean out all pipelines before installation of the regulator
and check to be sure the regulator has not been damaged
or has collected foreign material during shipping. For NPT
bodies, apply pipe compound to the male pipe threads. For
flanged bodies, use suitable line gaskets and approved
piping and bolting practices. Install the regulator in any
position desired, unless otherwise specified, but be sure
flow through the body is in the direction indicated by the
arrow on the body.
Note
It is important that the regulator be installed so that
the vent hole in the spring case is unobstructed at all
times. For outdoor installations, the regulator should
be located away from vehicular traffic and positioned
so that water, ice, and other foreign materials cannot
enter the spring case through the vent. Avoid placing
the regulator beneath eaves or downspouts, and be
sure it is above the probable snow level.
1. The pressure/temperature limits in this installation guide and any applicable
standard or code limitation should not be exceeded.